|
|
|
Mfr.
Sierra
Clutch housing seal kit for OMC stern drive
|
$23.79
-
$26.02
|
|
Mfr.
Sierra
| Mfr No. 18-6754
OMC Sterndrive / Cobra Tilt Motor. Replacement part for Sterndrive/Cobra Inboard/Outboard #382138 and Prestolite #ETK 4102, ETK 4001, ETK 4101. For all models 1963-77.
|
$163.88
|
|
Mfr.
Sierra
| Mfr No. 32-03192
OMC Sterndrive Cobra Trim Hose Manifold to Cylinder, Port Up. Replaces discontinued Sierra 18-2135. Replaces OMC 984024, 985617...
|
$69.97
|
|
Mfr.
Sierra
| Mfr No. 18-6755
This OMC Tilt Motor is a replacement part for Sterndrive/Cobra Inboard/Outboard #982706, #982058 and Prestolite #EVD 4001, EVD 4002. The tilt motor is made for all models except 2.5L, 3.0L - 1978-1985
|
$187.20
|
|
Mfr.
Sierra
- 18-6950 is a 50 amp replacement fuse for Sterndrive/Cobra Inboard/Outboard #982019
- 18-6951 is a 30 amp replacement fuse for Volvo Penta Inboard/Outboard #8
...
|
$4.12
-
$4.38
|
|
Mfr.
Sierra
| Mfr No. 18-2148
- Replaces: Mercruiser Inboard/Outboard #77442A1
- Fits all Sterndrive models: 120, 140, 160, 165, 888, 898, 228, 225-S, 233, 250, 260, 470 & 485
|
$76.94
|
|
Mfr.
Sierra
| Mfr No. 18-2291
- Replaces: Mercruiser Inboard/Outboard #25-60342A2
- Fits all Sterndrive models: 120, 140, 160, 165, 888, 228, 225-S, 233, 250, 260, 470 & 485
|
$49.47
|
|
Mfr.
Sierra
| Mfr No. 18-2437
Power Trim Hose. Fits King Cobra 1990-94. Pump to manifold down. Replaces OMC986144OMC3853921,
|
$30.56
|
|
Mfr.
Sierra
| Mfr No. 18-2438
Power Trim Hose. Fits King Cobra 1990-94. Pump to manifold up. Replaces OMC986145OMC3853922,
|
$33.43
|
|
Mfr.
Sierra
| Mfr No. 18-2442
Power Trim Hose. Fits King Cobra 1990-94. Manifold to cylinder port down. Replaces OMC986150OMC3853926,
|
$32.25
|
|
Mfr.
Sierra
- Replaces: Sterndrive/Cobra Inboard/Outboard #980183
- I/O 1964-86 except Cobra
|
$21.60
-
$30.15
|
|
Mfr.
Sierra
| Mfr No. 18-6779
Trim Motor. 1990 Cobra trim system. 1994 King Cobra trim system
|
$199.72
|
|
Mfr.
Sierra
| Mfr No. 18-6761
Tilt/Trim Motor. Older 3 wire design for most 3 4 6 cylinder outboards up to 1981, . Motor only. Replaces OMC387277 582048 582155 584107,
|
$195.89
|
|
Mfr.
Sierra
| Mfr No. 18-6285
Lifetime warranty on Sierra Tilt/Trim Motors and other Sierra Engine Parts. Thousands of engine parts, lowest prices, OEM and Sierra engine part technicians available.
|
$274.73
|
|
Mfr.
Sierra
| Mfr No. 18-6277
Tilt and Trim Assembly. Heavy Duty 2 wire connection. Flat blade shaft. OMC V-6 1993,
|
$260.63
|
|
Mfr.
Sierra
| Mfr No. 18-6280
Tilt Trim Assembly. Heavy Duty OMC M suffix [#183] 40 48 50 HP. 1989-92 2 wire. Hollow hex shaft,
|
$267.93
|
|
Mfr.
Sierra
| Mfr No. 18-6281
Tilt Trim Assembly. Heavy Duty. Used for OMC outboards. 75 Hp to 250 Hp . 1998 and Up,
|
$222.94
|
|
Mfr.
Sierra
| Mfr No. 18-6257
Lifetime warranty on Sierra Tilt/Trim Motors and other Sierra Engine Parts. Thousands of engine parts, lowest prices, OEM and Sierra engine part technicians available.
|
$437.23
|
|
Mfr.
Sierra
| Mfr No. 18-7634
OMC Cobra Trim Sending Unit, Replaces 984748 & 3850470, 18-7634...
|
$108.07
|
Above is the price you will be charged if you purchase this item(s). We do not show this price on the advertised page
because your price is below the manufacturer's suggested advertised price.
|
Products: 1 - 19 of 19
|
Page:
1
|
Post a question or comment about OMC Tilt & Trim to our online boating community.
actuater
Where is the solenoid actuater located on a 1987 OMC 4.3 liter 6 cyl trim /tilt? Submitted by: Blucky
There are two solenoids located on top of the engine.
1978 Chris craft OMC Tilt and Trim motors
The tilt/trim for my 1978 Chris Craft/ Viking deckboat with an OMC seems to have gone bad. What tilt/trim motor should I buy to replace it? Submitted by: AJ
Trim hose replacement
I have a ’93 Chris Craft w/ King Cobra outdrive. How do you replace the trim hoses on the outdrive? I’m told the outdrive has to be removed. Or is there a wrench that can be used to reach back under the transom?
Model = 584dppjvb Details are appriciated! Thanks,
Bill Submitted by: Bill A.
You’ll need to remove the drive and replace the bellows. Check the Gimbal Bearing at the same time. You don’t need to remove the power unit. I do suggest you get your hands on a service manual from Seloc. It tells you how to service the drive and make the correct shift cable adjustments. If you are interested, here is a link to the manuals. Seloc Marine Engine Repair and Service Manuals
omc outdrive for trim?
Im have a 1988 Bayliner 2155 5.7 engine, cobra omc outdrive. Do you use the up and down tilt switch of the outdrive to trim the boat when under way? Or will that harm the outdrive gears?
I had an older 1984 starfire boat and you could not use the outdrive to trim the boat, or it would distroy the gears for the tilt up and down.
Thanks for your help. Submitted by: 34 ford
The Cobra models can be trimmed. They use hydraulic cylinders for this function. As for a switch, any three position momentary rocker or toggle switch will work.
power tilt slipping slowly down
I have a 1991 Doral Spirit with a 4.3 liter 175 OMC inboard/outboard engine.
After setting the trim on my drive, it slowly drops down and will not stay in place. What part has to be replaced to prevent this from happening and how much will this cost me? Submitted by: william hitzig
Normally you would replace the valve body. It is no longer available so your only option is to re-seal it with a seal kit.
Show older >>
Thank you for submitting your review. Submissions are typically posted within 2 business days, pending approval.
Thank you for your submission. Most questions and comments are typically posted with a response within 2 business days.
|
|
|
