|
|
|
|
| Part No. |
Items |
Mfr No. |
Your Price |
| 85198 |
Power Tilt Fuse - 50 Amp |
18-6950
|
|
| 85199 |
Power Tilt Fuse - 30 Amp |
18-6951
|
|
|
|
|
| Part No. |
Items |
Mfr No. |
Your Price |
| 82405 |
Power Trim Cylinder Housing |
18-2148
|
|
|
|
|
| Part No. |
Items |
Mfr No. |
Your Price |
| 82469 |
Power Trim Cylinder O-Ring Kit |
18-2291
|
|
|
|
|
| Part No. |
Items |
Mfr No. |
Your Price |
| 158010 |
Power Trim Hose - OMC 3853921, 986144 |
18-2437
|
|
|
|
|
| Part No. |
Items |
Mfr No. |
Your Price |
| 157905 |
Power Trim Hose - OMC 3853922, 986145 |
18-2438
|
|
|
|
|
| Part No. |
Items |
Mfr No. |
Your Price |
| 158014 |
Power Trim Hose - OMC 3853926, 386150 |
18-2442
|
|
|
|
|
| Part No. |
Items |
Mfr No. |
Your Price |
| 82413 |
OMC Tilt Shaft, 310613 |
18-2156
|
|
| 161175 |
OMC Tilt Worm Bushing, 909499 |
909499
|
|
|
|
|
| Part No. |
Items |
Mfr No. |
Your Price |
| 157897 |
Tilt/Trim Motor - OMC 3853945, 986280, Volvo 986280 |
18-6779
|
|
|
|
|
| Part No. |
Items |
Mfr No. |
Your Price |
| 157968 |
Tilt/Trim Motor - OMC 387277, 582048, 582155, 584107 |
18-6761
|
|
|
|
|
| Part No. |
Items |
Mfr No. |
Your Price |
| 158951 |
Tilt/Trim Motor - OMC 433226 |
18-6285
|
|
|
|
|
| Part No. |
Items |
Mfr No. |
Your Price |
| 158944 |
Tilt/Trim Motor - OMC 435548 |
18-6277
|
|
|
|
|
| Part No. |
Items |
Mfr No. |
Your Price |
| 158946 |
Tilt/Trim Motor - OMC 437801 |
18-6280
|
|
|
|
|
| Part No. |
Items |
Mfr No. |
Your Price |
| 158947 |
Tilt/Trim Motor - OMC 438786, 439937, 5005254 |
18-6281
|
|
|
|
|
| Part No. |
Items |
Mfr No. |
Your Price |
| 158928 |
Tilt/Trim Motor - OMC 982957, 983195 |
18-6257
|
|
|
Above is the price you will be charged if you purchase this item(s). We do not show this price on the advertised page
because your price is below the manufacturer's suggested advertised price.
Post a question or comment about OMC Tilt & Trim to our online boating community.
actuater
Where is the solenoid actuater located on a 1987 OMC 4.3 liter 6 cyl trim /tilt? Submitted by: Blucky
There are two solenoids located on top of the engine.
1978 Chris craft OMC Tilt and Trim motors
The tilt/trim for my 1978 Chris Craft/ Viking deckboat with an OMC seems to have gone bad. What tilt/trim motor should I buy to replace it? Submitted by: AJ
Trim hose replacement
I have a ’93 Chris Craft w/ King Cobra outdrive. How do you replace the trim hoses on the outdrive? I’m told the outdrive has to be removed. Or is there a wrench that can be used to reach back under the transom?
Model = 584dppjvb Details are appriciated! Thanks,
Bill Submitted by: Bill A.
You’ll need to remove the drive and replace the bellows. Check the Gimbal Bearing at the same time. You don’t need to remove the power unit. I do suggest you get your hands on a service manual from Seloc. It tells you how to service the drive and make the correct shift cable adjustments. If you are interested, here is a link to the manuals. Seloc Marine Engine Repair and Service Manuals
omc outdrive for trim?
Im have a 1988 Bayliner 2155 5.7 engine, cobra omc outdrive. Do you use the up and down tilt switch of the outdrive to trim the boat when under way? Or will that harm the outdrive gears?
I had an older 1984 starfire boat and you could not use the outdrive to trim the boat, or it would distroy the gears for the tilt up and down.
Thanks for your help. Submitted by: 34 ford
The Cobra models can be trimmed. They use hydraulic cylinders for this function. As for a switch, any three position momentary rocker or toggle switch will work.
power tilt slipping slowly down
I have a 1991 Doral Spirit with a 4.3 liter 175 OMC inboard/outboard engine.
After setting the trim on my drive, it slowly drops down and will not stay in place. What part has to be replaced to prevent this from happening and how much will this cost me? Submitted by: william hitzig
Normally you would replace the valve body. It is no longer available so your only option is to re-seal it with a seal kit.
Show older >>
Thank you for submitting your review. Submissions are typically posted within 2 business days, pending approval.
Thank you for your submission. Most questions and comments are typically posted with a response within 2 business days.
|
|
|
