|
|
|
Mfr.
Sea-Dog
| Mfr No. 321291-1
Sea-Dog, Hatch Adjuster, Stainless / Nylon...
|
$20.82
|
|
Mfr.
Sea-Dog
| Mfr No. 321650-1
Sea-Dog, Hatch Spring, Stainless. Has an internal wire that prevents the spring from being over-extended during normal use...
|
$11.35
|
|
Mfr.
Sea-Dog
| Mfr No. 321670-1
Hatch Springs are made of formed 7 stamped 304 stainless steel. Ideal for use on lighter hatches, dock boxes and
|
$21.25
|
|
Mfr.
Sea-Dog
| Mfr No. 321680-1
Hatch Springs are made of formed 304 stainless steel injection molded nylon. Big, heavy-duty spring that is idea
|
$29.35
|
|
Mfr.
Sea-Dog
| Mfr No. 321292-1
Formed and Stamped 304 Stainless/Nylon.
|
$28.37
|
|
Mfr.
Sea-Dog
Formed and Stamped 304 Stainless/Nylon.
|
$23.92
-
$25.49
|
Above is the price you will be charged if you purchase this item(s). We do not show this price on the advertised page
because your price is below the manufacturer's suggested advertised price.
|
Products: 1 - 6 of 6
|
Page:
1
|
Post a question or comment about Hatch Lifts & Gas Springs to our online boating community.
Replacing Hatch Support
Have a single worn Perko Hatch support Bracket 12” PR# 22483 that I would like to upgrade. It is for the bait station lid on a Lures 36’ Sportfisher. I am looking for something heavy duty or maybe a stainless steel gas shock. Could you advise of all necessary parts needed to accomplish this. Thanks in advance. Submitted by: Bob Butler
lift supports
I need to replace two Suspa lif supports # C16-00462. They are 20" in length and threaded on each end. Can you match? Submitted by: jimbilly
heavy top
I am a woodworker who has manufactured a bench seat that is 30"deep X 120" long and I am in need of a some sort of gas assisted hatchback type of lift. It weighs between 70-100lbs and can only use 2 lifts. Can anyone help?? Submitted by: Laura
What do I need to use with the Electronic Hatch Lifts by Lenco, 1200S?
I want to use the Electronic Hatch Lifts by Lenco, 1200S to lift the bed of a custom ’32 Ford pick up truck which weighs a few hundred LBS. What else will I need from you and will this part do the job? Submitted by: Bill
It will be best to have a relay in between the switch and lift, otherwise the switch will most likely fail prematurely. We recommend using the Continous Duty Starter Solenoid.
Is there a way to make this Lift Support open partially?
I purchased two of the Nautalift Gas Lift Supports, 20" to go on my 18 foot manta ray for the hood. I do not need the the shocks to go the entire 20" when open, so is there a way to compress these so I can install? Submitted by: Ricky
The Nautalift Gas Lift Supports, 20" must open or close completely. There is not a way to make it open part of the way. You will need to measure your opening and order the correct length for your application, or move the attachment point to accommodate the fully open length.
Show older >>
Thank you for submitting your review. Submissions are typically posted within 2 business days, pending approval.
Thank you for your submission. Most questions and comments are typically posted with a response within 2 business days.
|
|
|
