|
|
|
Mfr.
Sierra
| Mfr No. 18-9750-0
- Formulated for high operating pressure
- Anti-foam additives assure uniform flow with reduced air contamination in hydraulic systems
- Designed for
...
|
$6.50
|
|
Mfr.
Sierra
| Mfr No. ARC M525
- Replaces Merc# 18525A1
- Replaces Aqua Power# 2414
- Sierra #18-6771 Discontiued, replaced by Arco# ARC-M525
|
$37.38
|
|
Mfr.
Teleflex Morse
| Mfr No. PT2000
Dual Function Engine Trim Control, Pro Trim, PT2000. Fits any boat using one of the following TeleflexMorse steering systems...
|
$110.94
|
|
Mfr.
API Marine
| Mfr No. BHMB500
API New Power Trim Bracket, BHMB 500...
|
$179.73
|
|
Mfr.
API Marine
| Mfr No. SSFMB500
Power Trim Bracket, Floor Mount, Stainless Steel, SSFMB 500...
|
$127.03
|
|
Mfr.
API Marine
| Mfr No. SSFMB500-ASSY
API New Power Trim Bracket, FMB 500-ASSY...
|
$189.99
|
|
Mfr.
API Marine
| Mfr No. CE603-API
API New Power Trim Com End...
|
$109.09
|
|
Mfr.
API Marine
| Mfr No. WH476
Trim Motor Relay Kit, WH-476. Relays with harness...
|
$62.32
|
|
Mfr.
CMC
| Mfr No. 13022
- For Electric Hydraulic Tilt and Trim Kit PT-130
|
$92.31
|
|
Mfr.
O.M.C.
| Mfr No. 0980274
- Replacement tilt motor coupling for OMC sterndrive * this is a 2 piece unit and is sold by the piece
|
$111.08
|
|
Mfr.
Sierra
- For all Power Trim Equipped, Inline engines except models with the power trim pump mounted between the engine clamp brackets
- Small diameter (1/8" I.D.)
...
|
$42.26
-
$46.62
|
|
Mfr.
LubriMatic
| Mfr No. 11578
Lubrimatic, Power Trim, Tilt & Steering Fluid, 10 oz Tube. Formulated to provide the viscosity and lubricity necessary to insure proper pump performance and seal life...
|
$5.82
|
Above is the price you will be charged if you purchase this item(s). We do not show this price on the advertised page
because your price is below the manufacturer's suggested advertised price.
|
Products: 1 - 12 of 12
|
Page:
1
|
Post a question or comment about Tilt and Trim System Parts to our online boating community.
tilt and trim issues on a 200 EFI Mercury
The tilt and trim just started making a rough grinding noise. It kinda reminds you of a rotary hammer drill noise. The tilt and trim continues to go up and down without the noise changing. I am trying to also figure out the year of the motor and tilt. It is a 200 Merc EFI. Mercury 200 HP
XRi
Electronic fuel injection Serial # oC261267 Submitted by: jeff melton
Power Trim & Tilt Motor & wiring
I have a 1991 Mercury 175XRI outboard motor that the power tilt & trim motor and wiring harness that is completely burned (meltdown). What replacement motor & wiring harness do I need? Motor model # 1-175413L and Serial # ODO68654. Thanks. Submitted by: Tony
Tilt n Trim
My tilt only clicks the solenoid when I try to lift it or put it down. Its a 91 100 hp Merc. Where should I start looking for problems? Submitted by: Skippy
Try putting power directly the the tilt motor and see if runs. The blue wire is up and the green wire is down!
stern drive tilt and trim pump
My stern drive goes all the way down but would only go half way up and then the pump quits then stops making noise. Submitted by: Roly
Sounds like you need a new trim/tilt motor. What is the make model and year of the engine/drive package?
CMC - model 7050
CMC motor model 7050 wires burned up. Think I Need new motor. Got any ideal? Submitted by: Vic
Please contact CMC directly for a new motor.
Show older >>
Thank you for submitting your review. Submissions are typically posted within 2 business days, pending approval.
Thank you for your submission. Most questions and comments are typically posted with a response within 2 business days.
|
|
|
