|
|
|
Mfr.
Edson
Edson 30 GPM, Manual Diaphragm Pump, Offset Drive Bottom Inlet is designed to be emergency manual back-up pumps for small holding tanks...
|
$769.14
-
$1,032.72
|
|
Mfr.
Edson
| Mfr No. 165AL-18-150
Edson Compact Portable Pump Kits are complete pumping systems that include the #217 pump mounted on a Carrying Board with 32" Handle, hose fittings, hose...
|
$634.38
|
|
Mfr.
Edson
Edson 30 GPM Aluminum Manual Diaphragm Pump with Lever Action Bottom Inlet is designed to be emergency manual back-up pumps for small holding tanks...
|
$639.51
-
$643.83
|
|
Mfr.
Edson
Edson 18 GPM, Manual Diaphragm Pump, Vertical Mount is ideal for pumping the bilge, sewage collection or transfer, spill clean up, and pump-outs of marina sumps and holding tanks...
|
$552.22
-
$695.63
|
|
Mfr.
Edson
Edson 30 GPM, Manual Diaphragm Pump, Offset Drive Side Inlet is designed to be emergency manual back-up pumps for small holding tanks...
|
$769.14
-
$1,032.72
|
|
Mfr.
Edson
Edson Manual Diaphragm Pump, 30 GPM, Lever Action Side Inlet is designed to be emergency manual back-up pump for small holding tanks...
|
$652.47
-
$903.09
|
|
Mfr.
Edson
Manual Diaphragm Pump, 18 GPM, Lever Action Side Inlet with Lever Action Side Inlet is designed to be used as a bilge pump or general purpose pump for yachts or work boats...
|
$450.63
-
$721.88
|
Above is the price you will be charged if you purchase this item(s). We do not show this price on the advertised page
because your price is below the manufacturer's suggested advertised price.
|
Products: 1 - 7 of 7
|
Page:
1
|
Post a question or comment about Bilge Hand Pumps to our online boating community.
Manual Bilge Pump
The manual bilge pump was removed from an older boat that I just purchased. I’d like to replace it. Can you tell me if you have a manual bilge pump that connects to 1 1/2" hoses and fits through a 3 1/2" bulkhead hole? Submitted by: David
Looking for the choker valve for my urchin manual bilge pump
Looking for the choker valve for my urchin manual bilge pump. Submitted by: Nello
The valve is not available separately. You will need the entire Seal Kit.
Looking for an O-ring for an old manual bilge pump.
I have a bilge pump mounted in the vertical face of the helm seat on a Morgan 382 sail boat. It has an aluminum body and an aluminum cover that hinges down by inserting the pump handle in the cover and using it as a lever, then the handle inserts straight into the pump for use.The o-ring seal that holds the cover in place is broken and the cover stays open. The outside diameter of the o-ring is 3 1/8". The cover has the initials "SM" cast in relief. Can anyone help me find a replacement o-ring? Submitted by: BC
Most local farm supply stores or larger automotive stores can supply that. O-rings are measured by the ID and material thickness - 2-7/8 x 1/8" o-ring = 3-1/8" OD.
Thank you for submitting your review. Submissions are typically posted within 2 business days, pending approval.
Thank you for your submission. Most questions and comments are typically posted with a response within 2 business days.
|
|
|
